Infer: How Do You Know the Surface Water Is Not There Because the Sediment Is Saturated?
I have replaced a whole-business firm water-filter sediment cartridge, and it was easier than I thought it would exist. Hither's how I did information technology.
Why Use a Whole Business firm Filtration System?
"OH, CULLIGAN Homo!"
When a home is running off of a safely treated private well or your h2o has a loftier mineral and debris content, y'all tin can find an abundance of minerals, sediment, and even atomic number 26 in your drinking, bathing, and cooking water that needs to be filtered out. In the by, many people bought a whole-house filtration organisation and installed information technology simply for this purpose.
Nosotros ran beyond one of these properties and discovered it was well beyond time to alter the sediment cartridge, and so we decided to accept on the claiming. Existence our first try at such a thing, we took pictures of our gamble. Changing a water-sediment cartridge was a pretty easy task, even for starting time-timers like us; this is how we did it.
Home Plumbing Made Easy
K9keystrokes
H2o Filter Cartridge Replacement Guide
Following the written preview of steps ane through 7 listed here, a motion-picture show-past-picture guide will have you through the filter-alter procedure one step at a time with easy-to-follow directions for each photo. I recommend wearing rubber goggles during the project, as water tin can spray towards your face up, and information technology may have particles from the captured sediment of the old filter. You will besides want to place a bucket under the water-filtration assembly to catch any h2o equally it flows out of the housing during the projection.
Preview of Project Steps 1–7
- Turn off the water supply. Press the red pressure-relief button. Rotate handle to OFF or BYPASS position.
- Unscrew housing. Remove large O-ring, wipe it make clean, and prepare aside.
- Remove and discard used filter cartridge. Launder housing with dish soap and warm h2o. Rinse completely. Fill ane/3 with water. Add together about 1 tablespoon of bleach and scrub to disinfect. Rinse thoroughly.
- Lubricate O-ring with make clean silicone grease and insert it back into the groove. It is important to brand sure the O-band is seated level in the groove. Otherwise, the housing may not have a proper seal.
- Replace the new filter cartridge over the standpipe in the bottom of the housing.
- Screw housing onto cap and hand-tighten. Exercise NOT OVER-TIGHTEN. Make sure cap standpipe slips into cartridge.
- Turn on the water supply. Rotate handle slowly to ON position for valve-in-head units. Press the pressure-release button (if nowadays). Check for leaks before leaving installation.
Important Information Regarding Your New Filter Change
After installing the whole-firm sediment-filtration cartridge, run the water!
Afterward y'all have the filter changed and the housing sealed properly, you will need to run your firm water for about 5 minutes before using any. It is a good idea to run the tap water for drinking and bathing for nearly thirty seconds before using it for any consumer purpose. It will be apparent that the water sediments accept plant their style into the tap system, as the initial water that pours from your faucets will probably exist a lovely shade of yucky!
Turn Off Water Supply
K9keystrokes
Step 1: Water Supply Off and Pressure level Release
Plough off the h2o supply either at the valve-in-head or principal h2o feed to the filter. Press the ruby button to release any built-up pressure level, be conscientious as a stream of water comes shooting out when the release push is engaged.
Annotation: The scarlet push can be a great practical joke tool to use on someone who isn't aware of the thrust of water that shoots from the housing pressure-relief valve. Just make sure everyone has prophylactic goggles on!
Remove Housing
K9keystrokes
Stride two: Remove Housing and Clean O-Ring
Unscrew the housing unit and remove the big O-ring. The O-ring is in the housing and looks like a large diameter, just thin blackness safety band. You volition demand to wipe it clean with a soft cloth and place it to the side until it is time to replace it into the housing. Check that information technology is still in good shape, if not, society a new one.
Read More From Dengarden
Lubricate O-Ring
K9keystrokes
Step iii: Dispose of Old Filter and Clean Housing
Remove the dirty old filter and throw it abroad. Y'all will need to clean the housing by first rinsing out the bulk of dirt. Then utilize dish lather and warm water to launder the housing using a low abrasive sponge or cloth, and then rinse it completely. Fill up the housing 1/3 full with water so add about a tablespoon of bleach to the housing and scrub gently to sanitize the interior surface. Rinse very thoroughly and several times.
Step 4: Lubricate O-Ring
Using a clean silicone grease, lubricate the O-ring completely, being sure to comprehend the within as well equally the exterior surface of the o-ring. (It is very of import to use a silicone-based grease for this application, as the silicone will not cause the safety to swell or soften like a hydrocarbon-based grease will.) Replace O-ring back into its groove. Take extra care to properly seat the o-ring or the seal on the housing volition leak, water pressure could degrade, and your h2o supply could become vulnerable to bacteria.
Install New Water-Filter Cartridge
K9keystrokes
Step five: Install New Water-Filter Cartridge
Now replace the filter. Look into the housing and yous will meet a standpipe positioned at the center bottom. It is a circular-shaped molded component with a short plastic-looking pipe protruding (See photo #5). It is of import to fit the filter over this correctly, every bit this is the h2o admission port, thus this is where all of your water will be coming from for filtration before heading to your house taps. Endeavour to centre the filter on the standpipe.
Screw Housing to Cap
K9keystrokes
Pace 6: Spiral Housing to Cap
Supersede the housing with the filter cartridge by hand-screwing it to the cap. Be sure to get the filter centered over the cap'southward standpipe. You won't necessarily be able to visually position it but you will exist able to feel the standpipe slip easily into the cartridge opening. Have care Not to tighten the housing too much, it can scissure easily.
Step vii: Plough on Water Supply and Test Pressure level
Slowly rotate the inlet handle to turn the water supply dorsum on. Employ caution considering the water tin come up rushing in too rapidly, and this tin can blow the housing off and destroy the unit of measurement. So, plough the inlet valve slowly and experience as the pressure arrives so y'all can control it while it fills the housing. We replaced a filter with a valve-in-head unit, but the same measure out of caution must be used for whatsoever water supply inlet used. Relieve pressure level by pressing the ruby release push button, water volition rooster- tail out of the unit of measurement and so exist prepared to get sprayed a lilliputian (or place a towel over the unit while conducting this footstep). Make sure you lot have a skillful seal where the housing and cap meet before leaving the unit of measurement.
Whole House Water Filter
K9keystrokes
Water-Filter Cartridge-Replacement Project Conclusion
After completing the filter replacement projection, we ran the house water for several minutes. When nosotros first opened the faucets, a loud, unfamiliar racket raged from the pipes. Information technology was really startling at kickoff until we realized what the cause was. The water was very dirty looking and spit and sputtered intermittently for some time. Even flushing the toilets and testing the shower offered this experience.
We began to inquire the question, "Now what? Another unexpected project at this onetime holding?" Only then nosotros realized all the knocking and spitting stemmed from the air that had gotten into the pipes during the project. It is a common occurrence and i you lot should expect to meet when irresolute your h2o filter cartridge.
This commodity is authentic and truthful to the best of the author's knowledge. Content is for informational or entertainment purposes only and does not substitute for personal counsel or professional advice in business, financial, legal, or technical matters.
© 2011 India Arnold
India Arnold (author) from Northern, California on November 30, 2011:
dflood~ Cheque that the large black rubber gasket has been seated correctly, and that yous take returned the force per unit area valves (inlet, outlet) to the correct position. If these do non work, you may need to supercede your filter housing, or pressure level release button. Good luck!
dflood on Nov 29, 2011:
Did all the steps above and at present water is coming out of the red pressure release button. What did I practise wrong?
India Arnold (author) from Northern, California on September 05, 2011:
Mentum mentum~ Cheers for the well wishes, you are very sweetness. Information technology pleases me you feel that after reading the educational activity for changing a whole house water filter in this hub, that you have conviction to do it yourself! I appreciate you swinging past today.
Cheers~
K9
Mentum mentum from Philippines on September 05, 2011:
Nosotros accept a filtration organization installed under our kitchen sink. It looks like to what y'all have illustrated here. I have never worked on it merely with your hub guide, I call up I tin do the filter cartridge change.
Congrats on writing and winning so many plumbing hubs.
India Arnold (author) from Northern, California on September 03, 2011:
PegCole~ Thanks! I hope you give it a attempt yourself if you always have to alter a whole house water filter. Nosotros found it pretty piece of cake and kinda fun!
Certain appreciate your support!
HubHugs~
K9
Peg Cole from Due north Dallas, Texas on September 03, 2011:
Well documented and illustrated. Very thorough and understandable guide to this plumbing task. I feel like I could do this now.
India Arnold (author) from Northern, California on September 02, 2011:
Penny~ Wow, are you lot correct! I have learned and so much by having to do some plumbing things myself; and of form via my dad'south brilliance, who has rescued me more than once. Thanks for your supportive comments, I really capeesh it!
Thank you~
K9
SimeyC~ Thank you for the congrats and your kind words. I hope y'all have been enjoying the plumbing contest, every bit your winning work has been a wonderful contribution in "how-to"!
Cheers~
K9
Simon Melt from NJ, United states on September 02, 2011:
Crawly hub! In that location goes the bar style high!!! Great stuff - fully deserves the daily prize!
Bharat Arnold (author) from Northern, California on September 01, 2011:
HRoger~ Hey, Cheers so much for the nice comments and votes! I certain appreciate you stopping past!
Cheers~
K9
HRoger from Online where I tin be! on September 01, 2011:
Hey K9 this is a awesome HUB!
Great information, very creative!
You got all my votes:
Useful (1)
Funny (1)
Awesome (1)
Cute (1)
Interesting (one)
Take intendance and keep it upwards!
Source: https://dengarden.com/home-improvement/How-to-Replace-a-Culligan-Sediment-Cartridge-Filter-Models-HF-150-160-360-and-most-standard-sizes
0 Response to "Infer: How Do You Know the Surface Water Is Not There Because the Sediment Is Saturated?"
Post a Comment